Electrical Overview Welcome to the Electrical Onboarding for the 2025-2026 school year! Goals Learning What is a PCB (Printed Circuit Board)? What is a Schematic? How do you read a Schematic? Practical Soldering components on a PCB Debugging/Testing a PCB Reading a Schematic You can find the schematic for the PCB you will be working on here . The first three pages contain the actual schematic for the PCB, although you can mainly ignore the first page as it is purely for connections across sheets. A schematic is just a logical and visual representation of the PCB. The third (last) page of the pdf contains a top down view of the board with all of its layers. The schematic is full of symbols like some of the ones seen below. You may also noticed that next to each symbol or component there is a designator, like SW1 shown in the image below. These correspond 1-to-1 on what you will see physically, as also shown below. Understanding the Board After taking a look at the schematic, you may have noticed there are quite a few components spread throughout the board. What do all of these do? How do they work? If you don't understand everything at the end of this session, that is okay! We don't expect you to learn everything about every part on this board, rather we just want to give you a general overview of what is going on. Voltage Regulation In order to actually power your robot, you will be using a battery holder that takes four AA batteries. With each battery at 1.5 volts connected in series (chained together), our max voltage we will have to deal with is around 6 volts. While this is great for some applications, our Pico is powered by 5 volts. To solve this, we can use something called an LDO which is found at designator U1 . This will create a stable 5 volts from our unstable battery voltage. In our case, we only need this to power the Pico and then we use the 3.3 volt output (it has a LDO built in) on the pico to power everything else (explained later). At designator D1 you'll find a diode. This essentially ensures that power can only flow one direction, in the case of this diode it only flows towards the direction of the silver band (indicated in the picture below). The reason the board requires this is because when you have your computer plugged into the Pico (which provides power across the VBUS line) and the batteries connected, you don't want the battery power flowing back into your computer. Raspberry PI Pico The Raspberry PI Pico is our chosen microcontroller for this project. A microcontroller is more or less just a tiny computer that is used to interface with hardware components like motors, servos, sensors, etc. You will be given a presoldered pico for your robot. Line Sensors and Servos Both of these are fortunately pretty simple. The Line Sensors are powered via 3.3v from the Pico and have their data lines connected directly to the Pico as well. These are simply read in firmware by checking whether the signal is Low or High. The servos are powered straight from the battery and are driven directly off of the Pico. Motor Driver In order to control the motors in a safe and reliable way, we will make use of a Motor Driver . This small IC (Integrated Circuit) found at designator IC1 takes the control signals that the PICO produces and converts them to the power needed to drive the motors. Other than some capacitors nearby per the datasheet, there isn't much else here! LEDs The LEDs are pretty basic, you connect power and ground and they light up. Most importantly, you will see that there is a resistor before each LED. The purpose of these is to limit the flow of current into the LEDs which helps prevent burnout or any issues. They are polarized, which the long leg of the LED indicating the positive side, which is also indicated on the board. Capacitors To keep it simple for now, all of the capacitors on the board are meant to supply charge at a moments notice. Additionally, they help to filter out high frequency noise. Basically, in general you want these by most IC's and outputs. Soldering Basics Before we get to assembling, lets walk through a few rules and tips about soldering. But first, what is soldering? Soldering is a method to permanently attach a component to something like a printed circuit board. Typically, as shown in the graphic below, you use solder (a metal alloy) and melt it to create that connection. Step 1: Tinning This is a step that helps protect the tip of the soldering iron and can help in general use of transferring solder to the component/board. Start by letting the soldering iron heat up, clean the tip with the provided sponge, and then press some of the solder on the tip and let it flow for a moment. It doesn't need a lot, just enough for the tip to turn a similar color to the solder. Step 2: Soldering Well, there are only two steps here but this is a really big step. Lets start by mounting the component that you want to solder to the board. On the top side, place it through the board in the correct orientation (if you are confused here please ask a mentor) and bend the legs such that it won't fall out when you tip the board over. Next, lets heat up the pad of the area you want to solder. The pad is just the small metal circle (or square), known as a solder joint, that surrounds the hole. Finally, lets apply some solder to that pad. Continue holding the soldering iron on that solder joint and touch your solder onto it (the solder joint) at the same time. Try not to touch the solder directly to the tip of the iron at this point, the solder joint should be hot enough to melt the solder. You should end up with something that looks more or less like this! We will also try to wander around and verify your first solder to make sure you are on track! Important Notes Do not touch yourself or any other person with the metal tip of the soldering iron at any time. These irons get extremely hot and will cause harm. Whenever you finish with a soldering iron, be sure to clean the tip! This includes when you are passing it around between people. It can help keep your solder joints clean :) PCB Assembly Now that you have learned some of the basics on how to solder and what all of the components do, its time to start assembling! For all of those in your team that wishes to solder, you should try breaking up the components so that each person gets to solder one of each component as practice! You may not be able to finish your entire PCB. Below is a full list of components in the approximate order they should be soldered: D1 - Diode (silver ring towards LEDs) C(4/5) - 10uF Capacitors C(1/2/7/8/9/10/11) - 0.1Uf Capacitors C(6/12) - 100uf Capacitors (long leg towards trace) R(2/3/4/5) - 820 resistor (the tiny ones) R1 - 10k resistor (the big one) LED(1/2/3/4) - LEDs (any color) J1 - Screw Terminal U1 - LDO (will be given once all of the above are soldered and checked) Don't be afraid to ask for help! Soldering for the first time can be a scary process, but we are here to help you! If you and your team do not feel comfortable soldering your board, that is perfectly fine as well! Most importantly, if you get burned in any way immediately inform one of the officers so we can assist you as needed. The Finished Product After assembling your board, you should have something like below (the space in the centre is where the pico will be). Testing Now it is time to test your PCB! If there is enough time for this, contact one of the mentors and we will walk through the testing steps. If there isn't enough time, we will manually test your PCB to ensure all of the individual components work. We will test your PCB regardless of whether we got to test it in the session just to double check :)